• Vent Axia Kinetic Highflow L/H – 12 Room Complete MVHR Kit
1 1

Vent Axia Kinetic Highflow L/H – 12 Room Complete MVHR Kit

Vent Axia Kinetic Highflow L/H – 12 Room Complete MVHR Kit

SKU : KIT-MVHR-408451L-12

€5.545,96 EUR Excl. VAT: €4.621,63 EUR

  • For warranty information, please refer to the manufacturer’s warranty policy or contact them directly.
View full details

Description

Vent Axia Kinetic Highflow L/H – 12 Room Complete MVHR Kit

This complete whole-house MVHR package is generated from BPC's current ventilation design and material-list logic around the exact Vent Axia Kinetic Highflow L/H (180mm 660m3/h @ 100Pa) (408451L). It is intended as a ready-to-buy reference kit for a representative 12-room home of approximately 230 m².

Reference design

  • Reference room mix: 5 bedroom(s), 1 living room(s), 1 other habitable room(s), 1 kitchen(s), 3 bathroom(s), 1 utility room(s) and 0 WC(s)
  • Calculated reference airflow: 248.4 m³/h
  • Selected unit design capacity used by BPC: 429.0 m³/h
  • Manufacturer maximum airflow stored in the design catalogue: 660.0 m³/h
  • 180mm main duct configuration with radial room distribution
  • Manufacturer: Vent-Axia
  • The unit, controls and ducting accessories below are generated by the same BOM engine used in the BPC design workflow.

Unit variant

  • Left-hand unit configuration

Important sizing note: this is a preset reference package, not a substitute for a project-specific ventilation design. Floor area, occupancy, bedrooms, wet rooms, duct routes and installation constraints can change the required airflow and material quantities. If your property differs materially from the reference configuration, send BPC your plans for a design check before ordering.

What's included

SKU Item Qty
QV-125AVP-S 125mm - Quiet-Vent supply air valve PVC (white) 7
QV-125AVP-E 125mm - Quiet-Vent extract air valve PVC (white) 6
QV-P180M-2 QV - 180mm - Metal Pipework x 2 meter 4
QV-C180MM QV- 180mm - Metal Male Coupling 3
QV-B90180M QV-180mm - Metal B90º Vent Pressed Bend with seals 10
QV180F-SILENCER Quiet-Vent 180mm x 500mm - Flexi insulated sound attenuator with adaptors 2
INS25 QV 25mm - 1m Foil Back Glass Fibre Insulation (1.2m x 1 m) 7
QV-SSC180WM 180mm Wall Cowl 2
CRC170-185 180mm Flexible Connector 4
BS50 Builders Strap Roll (10m /12*0.8cm) 2
ST75 75mm - Roll Silver Foil Tape (45 meters, 30 Microns) 2
SE380 Metal Sealant 1
QV75P-HP QV 75mm - 50 Metre Antibacterial Radial pipe (use QV rings) 5
QV75-PLEN Quiet-Vent 75mm Plenum 13
QV-75SR Quiet-Vent 75mm - Standard Sealing Ring (pack of 10) 6
QV75-15180RE Quiet-Vent 15 Pt Rear Entry Distribution box -180 spigot (75mm) with 4 x blanking caps 2
408451L Vent Axia Kinetic Highflow L/H (180mm 660m3/h @ 100Pa) 1
443283C Vent Axia Digital controller - hard wired (Sentinel Kinetic Only) 1

Frequently Asked Questions

  • What is a single room MVHR unit?

    A single room MVHR unit is a compact heat recovery ventilation unit designed to ventilate one room or a specific area. It helps extract stale air while bringing in fresh air and recovering heat from the outgoing air.

  • Where can single room MVHR units be used?

    Single room MVHR units are often used in retrofit projects, apartments, extensions, bedrooms, living spaces and other areas where targeted ventilation is required.

  • Do single room MVHR units need ductwork?

    Most single room MVHR units do not require a full ductwork system. They are usually installed through an external wall, although installation requirements vary by product.

  • How noisy are single room MVHR units?

    Noise levels vary by model and operating speed. Correct sizing and installation help keep operating noise low, particularly when the unit can run at lower background speeds.

  • Can multiple single room MVHR units be linked together in one property?

    Some single-room MVHR systems support paired or synchronised operation, while others operate independently. Always check the compatibility and control options of the specific model.