Vent Matika EKA NIS duct heater
Description
The Vent Matika EKA NIS range of electric duct heaters are Used in ventilation systems as heaters for comfort, or preheaters, to protect the ventilation unit from frost
The Vent Matika EKA NIS range of electric duct heaters are controlled by an external 0 to 10v DC signal from a compatible MVHR unit or independent controller
BPC Ventilation are the largest independent MVHR specialists and supply lifetime technical support on our top-quality systems,
Key Features
- Controlled via a 0 to 10v DC signal
- Internal temperature regulator
- May be used as a Pre Heater or a Post Heater
- Twin overheating protection
- Easy to use screw terminals
- Rubber sealed ductwork connections
- Can be installed both horizontally and vertically
- Stainless steel heating element
- Aluzinc Casing
- CE, RoSH & Reach certified
Control Options
- 0-10v sensor from a compatible MVHR unit or independent controller will allow 0-100% control of the heaters power
Overheating Protection
Two overheat protection thermostats are installed in the electrical circular heater EKA.
The first one with automatic reset, turns off the heating when the temperature reaches 50 °C and turns on when the temperature drops below 50 °C.
The second with manual safety reset, turns off the heating when the temperature reaches 100 °C. In
this case you need to figure the cause of the overheating of the heater. Eliminate the overheating cause and press the RESET button on the heaters cover.
Construction
Manufactured of from Aluzinc coated steel which is high temperature proof
Mounting
Heaters can only be installed inside away from moisture and mounted horizontally with the electrical connection box facing upwards or sideways and vertically (only if the air flow direction upwards).
Installation
Temperature
The maximum temperature of the output is 50 °C.
Dimensions
Models
These models are kept in stock, but other sizes and power outputs are available to order and please contact our team for cost and availability
- 100mm - 0.6kw Electric Duct Heater - EKA-NIS 100-0.6
- 125mm - 1.2kw Electric Duct Heater - EKA-NIS-125-1.2
- 160mm - 1.2kw Electric Duct Heater - EKA-NIS-160-1.2
- 160mm - 2.4kw Electric Duct Heater - EKA-NIS-160-2.4
- 200mm - 3.0kw Electric Duct Heater - EKA-NIS-200-3.0
- 250mm - 3.0kw Electric Duct Heater - EKA-NIS-250-3.0
Optional accessories
PTC Airflow sensor– Unit mounted sensor for electronic protection from insufficient airflow. The heater is only allowed to work if the airflow velocity is 1,5m/s or higher
PS Differential Pressure Switch – a unit mounted pressure switch that provides mechanical protection against loss or insufficient airflow. The heater if not allowed to heat unless a minimum airflow of 1,5m/s is reached.
(Note -due to required velocity the PTC or PS option may not work on some smaller domestic MVHR or MEV systems with low airflow rates)
PTC/PS – Sensor for minimum air velocity detection and diff. pressure switch for air flow detection
PTC/K – Sensor for minimum air velocity detection and contactor for overheating protection
2NTC – 2 sensors for the air temperature measuring
PTC/2NTC – Sensor for min. air velocity detection and 2 sensors for the air temperature measuring
By ordering the PS, an internal contactor for power supply is added to the heater as well.
BPC Support
We don’t sell boxes; we provide a service that few can match
- Free Lifetime Technical support on purchased items
- Largest independent MVHR suppliers
- Lowest cost on full systems guaranteed
- Inhouse design Team
- Inhouse certified training
- Largest range and stock available
- Worldwide delivery options
- MVHR Solutions available from Value to Prestige housing
